Understanding Essential Plumbing Skills is Vital for Installing a Bathtub
Understanding Essential Plumbing Skills is Vital for Installing a Bathtub
Blog Article
Are you trying to locate answers about How to Install a Bathtub Yourself?

Mounting a tub isn't specifically brain surgery, but it does require strong plumbing, woodworking, and also occasionally, tiling abilities. Changing an old bathtub with a new one is also a reasonably tough project. If the old tub is conveniently accessible, the job can relocate easily; if you have to open a wall surface to eliminate the old tub and also position the new tub, the job is much harder. In either situation, the project is within a house handyman's skills, although you will certainly need an assistant to move out the old tub as well as embeded in the new one. Ensure you have actually certified yourself for the task as well as fit attempting it. As opposed to hiring a specialist to take over a halfway-completed job, it is far better to take into consideration utilizing one before you start. Chances are you may require a specialist plumber to make tube connections.
This article will help you set up a new bath tub in your shower room if you have currently purchased a brand-new bathtub as well as don't require to transform the plan of your previous water supply pipelines.
Your devices as well as material list need to consist of the following:
Removing Old Touches
If you need to replace old taps with new ones as a part of your installation, then the first thing you must do is detach the water system. After doing so, turn on the faucets to drain any type of water remaining in the system. The process of getting rid of the existing taps can be rather problematic because of the limited gain access to that is frequently the case.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipes to the faucets. Have a fabric prepared for the staying water that will certainly come from the pipes. When the supply pipes have actually been removed, make use of the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will need to stop the single taps from transforming throughout this process. When the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleaned up of any type of old securing compound.
Before carrying on to fit the brand-new taps, contrast the pipe links on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is required for the new taps to fit.
Suitable New Touches
If the tails of the new taps are plastic, then you will need a plastic port to stop damages to the thread. One end of the adapter fits on the plastic tail of the faucet and the other end offers a link to the current supply pipelines.
If you require to fit a monobloc, then you will require reducing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, place the faucet in the mounting hole in the bath/basin guaranteeing that the washing machines remain in area in between the tap and the sink. Protect the faucet in position with the manufacturer offered backnut. As soon as the faucet is securely in place, the supply pipes can be attached to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with normal faucet connectors. The previous kind needs to be connected to the faucet ends initially, tightening just by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Installing the Bath tub
Making use of the two wood boards under its feet, put the bath tub in the called for position. The wood boards are valuable in uniformly spreading the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto four small factors.
The next goal is to make sure that the bathtub is leveled all round. This can be attained by inspecting the level and also changing the feet on the bath tub till the spirit level reads level.
To set up faucets, fit the bottom of the outermost versatile faucet adapter to the proper supply pipe by making a compression join; after that do the very same for the other faucet.
Turn on the water and inspect all joints as well as new pipework for leakages and tighten them if needed. Load the bathtub and likewise inspect the overflow electrical outlet and also the regular outlet for leakages.
Lastly, repair the bath paneling as described in the maker's instruction manual. Tiling as well as sealing around the tub must wait till the bath tub has been utilized a minimum of once as this will settle it into its last placement.
Getting ready for the Installment
Firstly, the sustaining structure provided with the bath ought to be fitted (if required) according to the producer's instructions. Next off, fit the taps or mixer to the tub. When fitting the faucet block, it is necessary to see to it that if the tap comes with a plastic washing machine, it is fitted in between the bathroom and also the taps. On a plastic bath, it is also practical to fit a supporting plate under the taps system to stop stress on the bath tub.
Fit the versatile faucet connectors to the bottom of the two taps utilizing 2 nuts and also olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet through the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. See to it you utilize all of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom ought to now be ready to be suited its last placement.
Tiling Around the Tub
In the location where the bath satisfies the floor tile, it is needed to secure the accompanies a silicone rubber caulking. This is very important as the installation can move sufficient to fracture an inflexible seal, causing the water to penetrate the wall in between the bath as well as the tiling, leading to problems with moisture and also possible leakages to the ceiling below.
You can choose from a variety of coloured sealers to blend in your components and fittings. They are sold in tubes as well as cartridges, and are capable of securing gaps up to a size of 3mm (1/8 inch). If you have a larger gap to load, you can load it with spins of soaked newspaper or soft rope. Remember to always fill up the bathtub with water prior to securing, to enable the motion experienced when the bathtub is in use. The sealer can crack rather early if you do not consider this activity prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also conveniently available on the market. It is recommended to fit the floor tiles making use of waterproof or waterproof glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

Hopefully you enjoyed our post on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thanks so much for taking a few minutes to read our short article. Enjoyed our blog posting? Please share it. Help someone else locate it. Thanks for your time. Visit again soon.
Top service? Contact. Report this page